Muganlı, Zülal and Bütün, İsmail and Gharıb, Ghazaleh and Koşar, Ali (2024) "Electricity generation using a microbial 3D bio-anode embedded bio-photovoltaic cell in a microfluidic chamber", Energy Advances, Vol.3, No.10, 2439-2452 (ESCI)

Özogul, Beyzanur and Akar, Ünal and Mercimek, Rabia and Rokhsar Talabazar, Farzad and Seyedmirzaei Sarraf, Seyedali and Sheibani Aghdam, Araz and Ansari Hamedani, Ali and Villanueva, Luis Guillermo and Grishenkov, Dmitry and Amani, Ehsan and Elverdi, Tugrul and Ghorbani, Morteza and Koşar, Ali (2024) "Hydrodynamic cavitation-induced thrombolysis on a clot-on-a-chip platform". Published Online First https://dx.doi.org/10.1002/anbr.202400112

Ebrahimpour Ahmadi, Vahid and Güler, Tayfun and Amin, Saifa and Apak, Ahmet Muhtar and Apak, Alper and Parlak, Murat and Tastan, Umur and Kaya, İsmet İnönü and Sadaghiani, Abdolali Khalili and Koşar, Ali (2024) "Effect of graphene coating on flow boiling in a minichannel at sub-atmospheric pressures", International Journal of Heat and Mass Transfer, Vol.229 (SCI)

Rokhsar Talabazar, Farzad and Baresel, Christian and Ghorbani, Reza and Tzanakis, Iakovos and Koşar, Ali and Grishenkov, Dmitry and Ghorbani, Morteza (2024) "Removal of per- and polyfluoroalkyl substances (PFAS) from wastewater using the hydrodynamic cavitation on a chip concept", Chemical Engineering Journal, Vol.495 (SCI)

Kantarcıoğlu Mazmanoğlu, Işık and Gaszek, Ilona K. and Güçlü, Tandaç Fürkan and Yildiz, M. Sadik and Atılgan, Ali Rana and Toprak, Erdal and Atılgan, Canan (2024) "Structural shifts in TolC facilitate efflux-mediated β-lactam resistance", Communications Biology, Vol.7, No.1 (SCI)

Ma, M. and Welles, N. and Svitelskiy, O. and Yanık, Cenk and Kaya, İsmet İnönü and Hanay, M. S. and Paul, M. R. and Ekinci, K. L. (2024) "Mode-dependent scaling of nonlinearity and linear dynamic range in a NEMS resonator", Applied Physics Letters, Vol.125, No.8 (SCI)

Karacaoğlu, Beyza and Koçer, Anıl Tevfik and İnan, Benan and Bütün, İsmail and Mercimek, Rabia and Ghorbani, Morteza and Koşar, Ali and Balkanlı, Didem (2024) "Microfluidic chip-assisted separation process and post-chip microalgae cultivation for carotenoid production". Published Online First https://dx.doi.org/10.1007/s10811-024-03337-4

Saeidiharzand, Shaghayegh and Sadaghiani, Abdolali Khalili and Orejon, Daniel and Sefiane, Khellil and Koşar, Ali (2024) "Biphilic functional surfaces for frost prevention and efficient active defrosting". Published Online First https://dx.doi.org/10.1002/admi.202400412

Basaran, Mustafa and Turkmen, Halit Suleyman and Yıldız, Mehmet (2024) "Sensor-enhanced thick laminated composite beams: manufacturing, testing, and numerical analysis", Sensors, Vol.24, No.16 (SCI)

Maleki, Mohammadamin and Rokhsar Talabazar, Farzad and Koşar, Ali and Ghorbani, Morteza (2024) "On the spatio-temporal dynamics of cavitating turbulent shear flow over a microscale backward-facing step: a numerical study", International Journal of Multiphase Flow, Vol.177 (SCI)

Abdelrahman, Amr Mustafa and Tebyani, Seyedreza and Rokhsar Talabazar, Farzad and Tabar, Saba Aghdam and Berenji, Nastaran Rahimzadeh and Sheibaniaghdam, Araz and Koyuncu, Ismail and Koşar, Ali and Guven, Huseyin and Ersahin, Mustafa Evren and Ghorbani, Morteza and Ozgun, Hale (2024) "The flow pattern effects of hydrodynamic cavitation on waste activated sludge digestibility", Chemosphere, Vol.357 (SCI)

Özyiğit, Samet and Mehdipour Aghbolagh, Mostafa and Al-Nadhari, Abdulrahman Saeed Abdulqader and Tabrizi, Arvin T. and Doğan, Semih and Dericiler, Kuray and Beylergil, Bertan and Yıldız, Mehmet and Saner Okan, Burcu (2024) "A comprehensive experimental study on the effects of hexagonal boron nitride particle size and loading ratio on thermal and mechanical performance in epoxy composites", Journal of Composite Materials, Vol.58, No.13 (SCI)

Barzegar Osgouei, Ali and Karimi, Sasan and Şaş Çaycı, Hatice Sinem and Yıldız, Mehmet (2024) "Enhancing interlaminar bonding quality estimation in laser-assisted fiber placement of CF/PEKK composites: a correction factor approach for improved prediction of intimate contact", Composites Part A: Applied Science and Manufacturing, Vol.181 (SCI)

Karimzadehkhoei, Jalal and Sorayani Bafqi, Mohammad Sajad and Dericiler, Kuray and Doustdar, Omid and Saner Okan, Burcu and Koşar, Ali and Sadaghiani, Ali (2024) "Upcycled graphene nanoplatelets integrated fiber-based Janus membranes for enhanced solar-driven interfacial steam generation". Published Online First http://dx.doi.org/10.1039/D4LF00082J

Farrokhnemoun, Darya and Sajjadivand, Seyyedehshahrzad and Parapari, Sorour Semsari and Sturm, Saso and Ow-Yang, Cleva W. and Gülgün, Mehmet Ali (2024) "Influence of sodium hydroxide on phase transformation of gamma alumina to alpha alumina", Journal of the American Ceramic Society, Vol.107, No.5, 3451-3463 (SCI)

Ateş, Ayşenur and Yağcı, Vedat and Malyemez, Muhammed Çağlar and Parlak, Murat and Sadaghiani, Abdolali Khalili and Koşar, Ali (2024) "Flow dynamics characteristics of flow boiling in minichannels with distributed pin fin structures", International Journal of Thermal Sciences, Vol.199 (SCI)

Karimi, Sasan and Yousefi Louyeh, Pouya and Barzegar Osgouei, Ali and Yıldız, Mehmet and Şaş Çaycı, Hatice Sinem (2024) "A study of post-processing for AFP-fabricated thermoplastic composites with void content and air permeability characterization", Journal of Reinforced Plastics and Composites, Vol.43, No.9-10, 490-503 (SCI)

Durmuş Sayar, Ayşe and Tansan, Murat and Çinko Çoban, Tuğçe and Serttan, Dilay and Dızman, Bekir and Yıldız, Mehmet and Ünal, Serkan (2024) "Incorporation of graphene nanoplatelets into fiber-reinforced polymer composites in the presence of highly branched waterborne polyurethanes", Polymers, Vol.16, No.6 (SCI)

Zoghipour, Pouya and Kefal, Adnan and Yıldız, Mehmet (2024) "Structural analysis of sandwich plates with variable stiffness composite skins and functionally graded cores using refined zig-zag theory". Published Online First https://dx.doi.org/10.1080/15376494.2024.2323098

Sharbati, Pouya and Sadaghiani, Abdolali Khalili and Koşar, Ali (2024) "On the effect of static and dynamic contact angles on humid air condensation heat transfer", International Journal of Heat and Mass Transfer, Vol.219 (SCI)

Kömürcü, Emre and Kefal, Adnan and Abdollahzadeh, M. A. and Basoglu, M. F. and Kısa, Erdal and Yıldız, Mehmet (2024) "Towards composite suspension control arm: conceptual design, structural analysis, laminate optimization, manufacturing, and experimental testing", Composite Structures, Vol.327 (SCI)

Vakilha, M. and Saghatchi, Roozbeh and Alexiadis, A. and Yıldız, Mehmet and Shadloo, M. S. (2024) "A fully explicit incompressible smoothed particle hydrodynamics approach for modeling transient heat transfer and thermo-capillary flows", Computers and Fluids, Vol.269 (SCI)

Kozalak, Gül and Koşar, Ali (2023) "Autophagy-related mechanisms for treatment of multiple myeloma", Cancer Drug Resistance, Vol.6, No.4, 838-857 (ESCI)

Yıldırım, Ceren and Tabrizi, Isa Emami and Al-Nadhari, Abdulrahman Saeed Abdulqader and Topal, Serra and Beylergil, Bertan and Yıldız, Mehmet (2023) "Characterizing damage evolution of CF/PEKK composites under tensile loading through multi-instrument structural health monitoring techniques", Composites Part A: Applied Science and Manufacturing, Vol.175 (SCI)

Behroozi Kohlan, Taha and Ateşpare, Asu Ece and Yıldız, Mehmet and Menceloğlu, Yusuf Z. and Ünal, Serkan and Dızman, Bekir (2023) "Amphiphilic polyoxazoline copolymer-imidazole complexes as tailorable thermal latent curing agents for one-component epoxy resins", ACS Omega, Vol.8, No.49, 47173-47186 (SCI)

Işık, Murat and Yıldız, Mehmet and Seçer, Ragıp Orkun and Sen, Ceren and Bilgin, Guney Mert and Orhangul, Akin and Akbulut, Guray and Javidrad, Hamidreza and Koç, Bahattin (2023) "Fabrication of electron beam melted titanium aluminide: the effects of machining parameters and heat treatment on surface roughness and hardness", Metals, Vol.13, No.12 (SCI)

Ranjbar Aghjehkohal, Amin and Taghizadeh Tabrizi, Arvin and Yıldız, Mehmet (2023) "Electrochemical hydrogen storage of synthesized heterostructure of hexagonal boron nitride-carbon nano tube", Journal of Alloys and Compounds, Vol.962 (SCI)

Dericiler, Kuray and Hezarkhani, Marjan and Emami Tabrizi, Isa and Doğan, Semih and Berktaş, İlayda and Erdem, Emre and Advani, Suresh G. and Yıldız, Mehmet and Şaş Çaycı, Hatice Sinem and Saner Okan, Burcu (2023) "Effect of interleaved electrolyte forms on macro-scaled structural hybrid supercapacitors with asymmetric configurations of graphene-coated carbon fabric electrodes", Applied Composite Materials, Vol.30, No.5, 1435-1451 (SCI)

Cagatay Karakan, M. and Ari, Atakan B. and Kelleci, Mehmet and Yanık, Cenk and Kaya, İsmet İnönü and Taştan, Öznur and Selim Hanay, M. (2023) "Vapor sensing of colorectal cancer biomarkers in isolation by bare and functionalized nanoelectromechanical sensors", IEEE Sensors Journal, Vol.23, No.18, 21113-21120 (SCI)

Barzegar Osgouei, Ali and Karimi, Sasan and Sukur, Emine Feyza and Şaş Çaycı, Hatice Sinem and Yıldız, Mehmet (2023) "Effect of fiber orientation on temperature history during laser-assisted thermoplastic fiber placement", Journal of Reinforced Plastics and Composites, Vol.42, No.17-18, 953-968 (SCI)

Çetin, Ebru and Güçlü, Tandaç Fürkan and Kantarcıoğlu, Işık and Gaszek, Ilona K. and Toprak, Erdal and Atılgan, Ali Rana and Dedeoglu, Burcu and Atılgan, Canan (2023) "Kinetic barrier to enzyme inhibition is manipulated by dynamical local interactions in E. coli DHFR", Journal of Chemical Information and Modeling, Vol.63, No.15, 4839-4849 (SCI)

Maleki, Mohammadamin and Rokhsar Talabazar, Farzad and Seyedmirzaei Sarraf, Seyedali and Sheibani Aghdam, Araz and Bayraktar, Songül and Tuzcuoğlu, Ehsan and Koşar, Ali and Ghorbani, Morteza (2023) "Detergent dissolution intensification via energy-efficient hydrodynamic cavitation reactors", ACS Omega, Vol.8, No.32, 29595-29607 (SCI)

Ali, Hafiz Qasim and Aydin, Mehmet Serhat and Awais Khan, Raja Muhammad and Yıldız, Mehmet (2023) "The role of "thickness effect" on the damage progression and crack growth inside the plain-woven carbon fiber composites", Composites Science and Technology, Vol.241 (SCI)

Tavakol Aghaei, Vahid and Ağababaoğlu, Arda and Bawo, Biram and Naseradinmousavi, Peiman and Yıldırım, Sinan and Yeşilyurt, Serhat and Onat, Ahmet (2023) "Energy optimization of wind turbines via a neural control policy based on reinforcement learning Markov chain Monte Carlo algorithm", Applied Energy, Vol.341 (SCI)

Kayacık, Sezen Ece and Kocuk, Burak and Yüksel, Tuğçe (2023) "The promise of EV-aware multi-period optimal power flow problem: cost and emission benefits", Sustainable Energy, Grids and Networks, Vol.34 (SCI)

Akgün, Sercan and Şenol, Cahit Orhun and Kılıç, Göktuğ and Tabrizi, Isa Emami and Yıldız, Mehmet (2023) "A novel damage evaluation of CFRPs under mode-I loading by using multi-instrument structural health monitoring methods", Engineering Fracture Mechanics, Vol.286 (SCI)

Alhamwi, Almotasem Belah and Atılgan, Canan and Sensoy, Ozge (2023) "Nonlocal effects of antibiotic-resistance-causing mutations reveal an alternative region for targeting on FtsW-penicillin-binding protein 3 complex of haemophilus influenzae", Journal of Chemical Information and Modeling, Vol.63, No.10, 3094-3104 (SCI)

Ergene, Arzu and Khabbazabkenar, Sirous and Şenol, Ayça and Günay, Ece and Kurt, Hasan and Topcu, Gökhan and Ow-Yang, Cleva W. (2023) "Oxide glass formers extending persistent luminescence in Eu and Dy co-doped strontium aluminates", Journal of Luminescence, Vol.257 (SCI)

Yılmaz, Çağatay and Ali, Hafiz Qasim and Yıldız, Mehmet (2023) "Monitoring and verification of micro-strain generated inside the laminate subjected to thermal loading through fiber bragg grating sensors and classical laminate theory", Polymer Composites, Vol.44, No.5, 2956-2965 (SCI)

Sharbati, Pouya and Sadaghiani, Abdolali and Koşar, Ali (2023) "New generation dielectrophoretic-based microfluidic device for multi-type cell separation", Biosensors, Vol.13, No.4 (SCI)

Goral, Levent and Sezen, Meltem and Ow-Yang, Cleva W. and Günhan, Büşra and Buyukaksoy, Aligul (2023) "Evolution of elemental distribution in single liquid precursor-derived nanocomposite solid oxide cell electrodes at nanoscale and its impact on electrochemical performance stability", Journal of Solid State Electrochemistry, Vol.27, No.3, 655-666 (SCI)

Ali, Hafiz Qasim and Khan, Raja M. A. and Tabrizi, Isa E. and Yıldız, Mehmet (2023) "An experimental multi-instrumental approach to understand the size effect on the damage propagation of plain-woven CFRP composites under shear loading", Journal of Composite Materials, Vol.57, No.5, 955-966 (SCI)

Zoghipour, Pouya and Hasim, K. A. and Kefal, Adnan and Yıldız, Mehmet (2023) "Implementation of shear-locking-free triangular refined zigzag element for structural analysis of multilayered plates with curvilinear fibers", Composite Structures, Vol.305 (SCI)

Ateş, Ayşenur and Parizad Benam, Behnam and Mohammadilooey, Mandana and Çelik, Süleyman and Serdyukov, Vladimir and Surtaev, Anton and Sadaghiani, Abdolali Khalili and Koşar, Ali (2023) "Pool boiling heat transfer on superhydrophobic, superhydrophilic, and superbiphilic surfaces at atmospheric and sub-atmospheric pressures", International Journal of Heat and Mass Transfer, Vol.201, No.Part-2 (SCI)

Rokhsar Talabazar, Farzad and Maleki, Mohammadamin and Sheibani Aghdam, Araz and Grishenkov, Dmitry and Ghorbani, Morteza and Koşar, Ali (2023) "Cavitation inception and evolution in cavitation on a chip devices at low upstream pressures", Physics of Fluids, Vol.35, No.1 (SCI)

Saghatchi, Roozbeh and Kolukısa, Deniz Can and Yıldız, Mehmet (2023) "Development of smoothed particle hydrodynamics method for modeling active nematics", International Journal for Numerical Methods in Engineering, Vol.124, No.1, 159-182 (SCI)

Sharani, Baidaa and Haghighi Poudeh, Leila and Elmas, Sinem and Şaş Çaycı, Hatice Sinem and Yıldız, Mehmet (2023) "Aspects of halloysite nanotubes integration in epoxy nanocomposites: curing kinetics and deformation mechanism", Polymer Composites, Vol.44, No.1, 574-591 (SCI)

Gul, Saher and Arican, Selin and Cansever, Murat and Beylergil, Bertan and Yıldız, Mehmet and Saner Okan, Burcu (2023) "Design of highly thermally conductive hexagonal boron nitride-reinforced PEEK composites with tailored heat conduction through-plane and rheological behaviors by a scalable extrusion", ACS Applied Polymer Materials, Vol.5, No.1, 329-341 (SCI)

Çetin, Ebru and Atılgan, Ali Rana and Atılgan, Canan (2022) "DHFR mutants modulate their synchronized dynamics with the substrate by shifting hydrogen bond occupancies", Journal of Chemical Information and Modeling, Vol.62, No.24, 6715-6726 (SCI)

Bütün, İsmail and Gharib, Ghazaleh and Yürüm, Alp and Alkan Gürsel, Selmiye and Koşar, Ali (2022) "Polymer based electricity generation inspired by eel electrocytes", International Journal of Energy Research, Vol.46, No.15, 22653-22663 (SCI)

Yılmaz, Abdurrahim and Karavelioğlu, Zeynep and Aydemir, Gizem and Demircali, Ali Anıl and Varol, Rahmetullah and Koşar, Ali and Uvet, Hüseyin (2022) "Microfluidic wound scratching platform based on an untethered microrobot with magnetic actuation", Sensors and Actuators B: Chemical, Vol.373 (SCI)

Piepoli, Sofia and Barakat, Sarah Mohammed Mohammed and Noğay, Liyne and Şimşek, Büşra and Akköse, Ümit and Taşkıran, Hakan and Tolay, Nazife and Gezen, Melike and Yeşilada, Canberk Yarkın and Tuncay, Mustafa and Adebali, Ogün and Atılgan, Canan and Erman, Batu (2022) "Sibling rivalry among the ZBTB transcription factor family: homodimers versus heterodimers", Life Science Alliance, Vol.5, No.11 (SCI)

Gharıb, Ghazaleh and Bütün, İsmail and Muganlı, Zülal and Kozalak, Gül and Namlı, İlayda and Seyedmirzaei Sarraf, Seyedali and Ebrahimpour Ahmadi, Vahid and Toyran, Erçil and Van Wijnen, Andre J. and Koşar, Ali (2022) "Biomedical applications of microfluidic devices: a review", Biosensors, Vol.12, No.11 (SCI)

Sheibani Aghdam, Araz and Rokhsar Talabazar, Farzad and Jafarpour, Mohammad and Koşar, Ali and Cebeci, Fevzi Çakmak and Ghorbani, Morteza (2022) "New nanofiber composition for multiscale bubble capture and separation", ACS Omega, Vol.7, No.44, 39959-39969 (SCI)

Ramezanzadeh, Shayan and Özbulut, Murat and Yıldız, Mehmet (2022) "A numerical investigation of the energy efficiency enhancement of oscillating water column wave energy converter systems", Energies, Vol.15, No.21 (SCI)

Behroozi Kohlan, Taha and Ateşpare, Asu Ece and Yıldız, Mehmet and Menceloğlu, Yusuf Z. and Ünal, Serkan and Dızman, Bekir (2022) "Synthesis and structure-property relationship of amphiphilic poly(2-ethyl- co-2-(alkyl/aryl)-2-oxazoline) copolymers", ACS Omega, Vol.7, No.44, 40067-40077 (SCI)

Sefiane, Khellil and Koşar, Ali (2022) "Prospects of heat transfer approaches to dissipate high heat fluxes: opportunities and challenges", Applied Thermal Engineering, Vol.215 (SCI)

Namlı, İlayda and Seyedmirzaei Sarraf, Seyedali and Sheibani Aghdam, Araz and Çelebi Torabfam, Gizem and Kutlu, Özlem and Çetinel, Sibel and Ghorbani, Morteza and Koşar, Ali (2022) "Hydrodynamic cavitation on a chip: a tool to detect circulating tumor cells", ACS Applied Materials and Interfaces, Vol.14, No.36, 40688-40697 (SCI)

Duman, Alp and Niazi, Soroush and Gharıb, Ghazaleh and Sadaghiani, Abdolali Khalili and Koşar, Ali (2022) "Self-assembled archaea bio-coatings in thermal-fluids systems: a study on adhesion optimization and energy efficiency", International Journal of Thermofluids, Vol.15 (NA)

Ti, C. and McDaniel, J. G. and Liem, A. and Gress, H. and Ma, M. and Kyoung, S. and Svitelskiy, O. and Yanık, Cenk and Kaya, İsmet İnönü and Hanay, M. S. and González, M. and Ekinci, K. L. (2022) "Dynamics of NEMS resonators across dissipation limits", Applied Physics Letters, Vol.121, No.2 (SCI)

Ansari Hamedani, Ali and Ow-Yang, Cleva W. and Hayat Soytaş, Serap (2022) "Silicon nanocrystals-embedded carbon nanofibers from hybrid polyacrylonitrile – TEOS precursor as high-performance lithium-ion battery anodes", Journal of Alloys and Compounds, Vol.909 (SCI)

Saghatchi, Roozbeh and Yıldız, Mehmet and Doostmohammadi, Amin (2022) "Nematic order condensation and topological defects in inertial active nematics", Physical Review E, Vol.106, No.1 (SCI)

Ali, Hafiz Qasim and Yilmaz, Çağatay and Yıldız, Mehmet (2022) "The effect of different tabbing methods on the damage progression and failure of carbon fiber reinforced composite material under tensile loading", Polymer Testing, Vol.111 (SCI)

Saeidiharzand, Shaghayegh and Sadaghiani, Abdolali Khalili and Koşar, Ali (2022) "Effect of membrane surface wetting on the performance of direct contact membrane distillation for seawater desalination", Cleaner Engineering and Technology, Vol.8 (NA)

Vasile, Bogdan Stefan and Nicoara, Adrian Ionut and Surdu, Vasile Adrian and Ene, Vladimir Lucian and Neacsu, Ionela Andreea and Stoica, Alexandra Elena and Oprea, Ovidiu and Boierasu, Iulian and Trusca, Roxana and Vrabec, Mirijam and Miklavic, Blaz and Sturm, Saso and Ow-Yang, Cleva W. and Gülgün, Mehmet Ali and Bundur, Zeynep Basaran (2022) "Fly-ash evaluation as potential EOL material replacement of cement in pastes: morpho-structural and physico-chemical properties assessment", Materials, Vol.15, No.9 (SCI)

Aboubakri, Akam and Sadaghiani, Abdolali Khalili and Akgönül, Sarp and Erdoğmuş, Abdullah Berkan and Baki, Murat and Can, Fatih and Şabanoviç, Asif and Koşar, Ali (2022) "Numerical and experimental investigation of the effect of micro restriction geometry on gas flows through a micro orifice", Fluids, Vol.7, No.5 (ESCI)

Emami Tabrizi, Isa and Kefal, Adnan and Seyyed Monfared Zanjani, Jamal and Yıldız, Mehmet (2022) "Damage growth and failure detection in hybrid fiber composites using experimental in-situ optical strain measurements and smoothing element analysis", International Journal of Damage Mechanics, Vol.31, No.4, 479-507 (SCI)

Kefal, Adnan and Diyaroğlu, Çağan and Yıldız, Mehmet and Oterkus, Erkan (2022) "Coupling of peridynamics and inverse finite element method for shape sensing and crack propagation monitoring of plate structures", Computer Methods in Applied Mechanics and Engineering, Vol.391 (SCI)

Surtaev, Anton and Koşar, Ali and Serdyukov, Vladimir and Malakhov, Ivan (2022) "Boiling at subatmospheric pressures on hydrophobic surface: bubble dynamics and heat transfer", International Journal of Thermal Sciences, Vol.173 (SCI)

Çaldağ, Hakan Osman and Demir, Ebru and Yeşilyurt, Serhat (2022) "A numerical and experimental investigation of rolling and sliding motion of rotating spheres inside a cylinder", Journal of Fluid Mechanics, Vol.935 (SCI)

Burak Okan, Osman and Turgut, Deniz and Atılgan, Canan and Atılgan, Ali Rana and Ozisik, Rahmi (2022) "Could network structures generated with simple rules imposed on a cubic lattice reproduce the structural descriptors of globular proteins?", Journal of Complex Networks, Vol.10, No.1 (SCI)

Rahimi, Mohammad Naqib and Kolukısa, Deniz Can and Yıldız, Mehmet and Ozbulut, Murat and Kefal, Adnan (2022) "A generalized hybrid smoothed particle hydrodynamics-peridynamics algorithm with a novel Lagrangian mapping for solution and failure analysis of fluid-structure interaction problems", Computer Methods in Applied Mechanics and Engineering, Vol.389 (SCI)

Parlak, Murat and Özsunar, Abuzer and Koşar, Ali (2022) "High aspect ratio microchannel heat sink optimization under thermally developing flow conditions based on minimum power consumption", Applied Thermal Engineering, Vol.201, No.Part A (SCI)

Emami Tabrizi, Isa and Öz, Fatih Ertuğrul and Seyyed Monfared Zanjani, Jamal and Mandal, Sefa Kemal and Yıldız, Mehmet (2022) "Failure sequence determination in sandwich structures using concurrent acoustic emission monitoring and postmortem thermography", Mechanics of Materials, Vol.164 (SCI)

Işık, Murat and Kısa, Erdal and Koç, Bahattin and Yıldız, Mehmet and Pehlivanoğulları, Barış and Orhangül, Akın and Akbulut, Güray (2021) "Topology optimization and manufacturing of engine bracket using electron beam melting", Journal of Additive Manufacturing Technologies, Vol.1, No.3 (NA)

Parizad Benam, Behnam and Sadaghiani, Abdolali Khalili and Yağcı, Vedat and Parlak, Murat and Sefiane, Khellil and Koşar, Ali (2021) "Review on high heat flux flow boiling of refrigerants and water for electronics cooling", International Journal of Heat and Mass Transfer, Vol.180 (SCI)

Abdollahzadeh, Mohammadamin and Tabrizi, Isa Emami and Kefal, Adnan and Yıldız, Mehmet (2021) "A combined experimental/numerical study on deformation sensing of sandwich structures through inverse analysis of pre-extrapolated strain measurements", Measurement: Journal of the International Measurement Confederation, Vol.185 (SCI)

Mohammadpour Chehrghani, Mirvahid and Abbasiasl, Taher and Sadaghiani, Abdolali Khalili and Koşar, Ali (2021) "Biphilic surfaces with optimum hydrophobic islands on a superhydrophobic background for dropwise flow condensation", Langmuir, Vol.37, No.46, 13567-13575 (SCI)

Aboubakri, Akam and Ebrahimpour Ahmadi, Vahid and Çelik, Süleyman and Sadaghiani, Abdolali Khalili and Sefiane, Khellil and Koşar, Ali (2021) "Effect of surface biphilicity on FC-72 flow boiling in a rectangular minichannel", Frontiers in Mechanical Engineering, Vol.7 (ESCI)

Saghatchi, Roozbeh and Özbulut, Murat and Yıldız, Mehmet (2021) "Dynamics of double emulsion interfaces under the combined effects of electric field and shear flow", Computational Mechanics, Vol.68, No.4, 775-793 (SCI)

Bilbey, Buse and Sezen, Meltem and Ow-Yang, Cleva W. and Çamiç, Büşra Tuğba and Buyukaksoy, Aligul (2021) "Formation, performance, and long-term stability of nanostructured Ni-YSZ thin film electrodes", ACS Applied Energy Materials, Vol.4, No.9, 9046-9056 (SCI)

Ansari Hamedani, Ali and Ow-Yang, Cleva W. and Hayat Soytaş, Serap (2021) "Mechanisms of Si nanoparticle formation by molten salt magnesiothermic reduction of silica for lithium-ion battery anodes", ChemElectroChem, Vol.8, No.16, 3181-3191 (SCI)

Emami Tabrizi, Isa and Sharani, Baidaa and Seyyed Monfared Zanjani, Jamal and Yıldız, Mehmet (2021) "Using digital image correlation for in situ strain and damage monitoring in hybrid fiber laminates under in-plane shear loading", Polymer Composites, Vol.42, No.8, 4029-4042 (SCI)

Eren, Guncem Ozgun and Sadeghi, Sadra and Bahmani Jalali, Houman and Ritter, Maximilian and Han, Mertcan and Baylam, Isinsu and Melikov, Rustamzhon and Onal, Asim and Oz, Fatma and Sahin, Mehmet and Ow-Yang, Cleva W. and Sennaroglu, Alphan and Lechner, Rainer and Nizamoglu, Sedat (2021) "Cadmium-free and efficient type-II InP/ZnO/ZnS quantum dots and their application for LEDs", ACS Applied Materials & Interfaces, Vol.13, No.27, 32022-32030 (SCI)

Kefal, Adnan and Emami Tabrizi, Isa and Yıldız, Mehmet and Tessler, Alexander (2021) "A smoothed iFEM approach for efficient shape-sensing applications: numerical and experimental validation on composite structures", Mechanical Systems and Signal Processing, Vol.152 (SCI)

Bahmani Jalali, Houman and Sadeghi, Sadra and Baylam, Isinsu and Han, Mertcan and Ow-Yang, Cleva W. and Sennaroglu, Alphan and Nizamoglu, Sedat (2021) "Exciton recycling via InP quantum dot funnels for luminescent solar concentrators", Nano Research, Vol.14, No.5, 1488-1494 (SCI)

Jafarpour, Mohammad and Sheibani Aghdam, Araz and Talebian Gevari, Moein and Koşar, Ali and Bayazıt, Mustafa Kemal and Ghorbani, Morteza (2021) "An ecologically friendly process for graphene exfoliation based on the "hydrodynamic cavitation on a chip" concept", RSC Advances, Vol.11, No.29, 17965-17975 (SCI)

Güçlü, Tandaç Fürkan and Atılgan, Ali Rana and Atılgan, Canan (2021) "Dynamic community composition unravels allosteric communication in pdz3", Journal of Physical Chemistry B, Vol.125, No.9, 2266-2276 (SCI)

Seyyed Monfared Zanjani, Jamal and Yousefi Louyeh, Pouya and Emami Tabrizi, Isa and Al-Nadhari, Abdulrahman Saeed Abdulqader and Yıldız, Mehmet (2021) "Thermo-responsive and shape-morphing CF/GF composite skin: full-field experimental measurement, theoretical prediction, and finite element analysis", Thin-Walled Structures, Vol.160 (SCI)

Hosseinpour Shafaghi, Ali and Rokhsar Talabazar, Farzad and Zuvin, Merve and Talebian Gevari, Moein and Villanueva, Luis Guillermo and Ghorbani, Morteza and Koşar, Ali (2021) "On cavitation inception and cavitating flow patterns in a multi-orifice microfluidic device with a functional surface", Physics of Fluids, Vol.33, No.3 (SCI)

Yanık, Cenk and Sazgari Ardakani, Vahid and Canatar, Abdülkadir and Vaheb, Yaser and Kaya, İsmet İnönü (2021) "Strong localization in suspended monolayer graphene by intervalley scattering", Physical Review B, Vol.103, No.8 (SCI)

Mohammadpour Chehrghani, Mirvahid and Abbasiasl, Taher and Sadaghiani, Abdolali Khalili and Koşar, Ali (2021) "Copper-based superhydrophobic nanostructures for heat transfer in flow condensation", ACS Applied Nano Materials, Vol.4, No.2, 1719-1732 (SCI)

Güçlü, Tandaç Fürkan and Kocatuğ, Nazlı and Atılgan, Ali Rana and Atılgan, Canan (2021) "N-terminus of the third PDZ domain of PSD-95 orchestrates allosteric communication for selective ligand binding", Journal of Chemical Information and Modeling, Vol.61, No.1, 347-357 (SCI)

Alexiadis, Alessio and Albano, Andrea and Rahmat, Amin and Yıldız, Mehmet and Kefal, Adnan and Özbulut, Murat and Bakırcı, Nadi and Garzon Alvarado, Diego Alexander and Duque-Daza, Carlos Alberto and Eslava-Schmalbach, Javier Hernando (2021) "Simulation of pandemics in real cities: enhanced and accurate digital laboratories", Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, Vol.477, No.2245 (SCI)

Rizvandi, Omid Babaie and Eskin, Murat Gökhan and Yeşilyurt, Serhat (2021) "Numerical modeling of anode-bleeding PEM fuel cells: effects of operating conditions and flow field design", International Journal of Hydrogen Energy (SI), Vol.46, No.5, 4378-4398 (SCI)

Haghighi Poudeh, Leila and Berktaş, İlayda and Ali, Hafiz Qasim and Saner Okan, Burcu and Yıldız, Mehmet (2020) "Toward next-generation carbon-based materials derived from waste and biomass for high-performance energy applications", Energy Technology, Vol.8, No.12 (SCI)

Saghatchi, Roozbeh and Rahmat, Amin and Yıldız, Mehmet (2020) "Electrohydrodynamics of a droplet in a highly confined domain: a numerical study", Physics of Fluids, Vol.32, No.12 (SCI)

Talebian Gevari, Moein and Niazi, Soroush and Karimzadehkhouei, Mehrdad and Şendur, Kürşat and Menguc, M. Pinar and Ghorbani, Morteza and Koşar, Ali (2020) "Deagglomeration of nanoparticle clusters in a "cavitation on chip" device", AIP Advances, Vol.10, No.11 (SCI)

Khan, Raja Muhammad Awais and Emami Tabrizi, Isa and Ali, Hafiz Qasim and Demir, Eralp and Yıldız, Mehmet (2020) "Investigation on interlaminar delamination tendency of multidirectional carbon fiber composites", Polymer Testing, Vol.90 (SCI)

Rahimi, Mohammad Naqib and Kefal, Adnan and Yıldız, Mehmet and Öterkuş, Erkan (2020) "An ordinary state-based peridynamic model for toughness enhancement of brittle materials through drilling stop-holes", International Journal of Mechanical Sciences, Vol.182 (SCI)

Sadaghiani, Abdolali Khalili and Rajabnia, Hossein and Çelik, Süleyman and Noh, H. and Kwak, H. J. and Nejatpour, Mona and Park, Hyun Sun and Acar, H. Y. and Mısırlıoğlu, Burç and Özdemir, Mehmed Rafet and Koşar, Ali (2020) "Pool boiling heat transfer of ferrofluids on structured hydrophilic and hydrophobic surfaces: the effect of magnetic field", International Journal of Thermal Sciences, Vol.155 (SCI)

Çaldağ, Hakan Osman and Yeşilyurt, Serhat (2020) "Acoustic radiation forces on magnetically actuated helical swimmers", Physics of Fluids, Vol.32, No.9 (SCI)

Aboubakri, Akam and Ebrahimpour Ahmadi, Vahid and Koşar, Ali (2020) "Modeling of a passive-valve piezoelectric micro-pump: a parametric study", Micromachines, Vol.11, No.8 (SCI)

Ijaz, Aatif and Yağcı, M. Barış and Ow-Yang, Cleva W. and Demirel, A. Levent and Miko, Annamaria (2020) "Formation of mesoporous silica particles with hierarchical morphology", Microporous and Mesoporous Materials, Vol.303 (SCI)

Hosseinpour Shafaghi, Ali and Rokhsar Talabazar, Farzad and Koşar, Ali and Ghorbani, Morteza (2020) "On the effect of the respiratory droplet generation condition on COVID-19 transmission", Fluids, Vol.5, No.3 (ESCI)

Piepoli, Sofia and Alt, Aaron Oliver and Atılgan, Canan and Mancini, Erika Jazmin and Erman, Batu (2020) "Structural analysis of the PATZ1 BTB domain homodimer", Acta Crystallographica Section D: Structural Biology, Vol.76, 581-593 (SCI, CPCI-S)

Talebian Gevari, Moein and Abbasiasl, Taher and Niazi, Soroush and Ghorbani, Morteza and Koşar, Ali (2020) "Direct and indirect thermal applications of hydrodynamic and acoustic cavitation: a review", Applied Thermal Engineering, Vol.171 (SCI)

Yetişgin, Abuzer Alp and Çetinel, Sibel and Zuvin, Merve and Koşar, Ali and Kutlu, Özlem (2020) "Therapeutic nanoparticles and their targeted delivery applications", Molecules, Vol.25, No.9 (SCI)

Erdem, Kaan and Ebrahimpour Ahmadi, Vahid and Koşar, Ali and Kuddusi, Lutfullah (2020) "Differential sorting of microparticles using spiral microchannels with elliptic configurations", Micromachines, Vol.11, No.4 (SCI)

Sazgari Ardakani, Vahid and Sullivan, Gerard and Kaya, İsmet İnönü (2020) "Interaction-induced crossover between weak antilocalization and weak localization in a disordered InAs/GaSb double quantum well", Physical Review B, Vol.101, No.15 (SCI)

Yılmaz, Çağatay and Topal, Serra and Ali, Hafiz Qasim and Tabrizi, Isa Emami and Al-Nadhari, Abdulrahman Saeed Abdulqader and Suleman, Afzal and Yıldız, Mehmet (2020) "Non-destructive determination of the stiffness matrix of a laminated composite structure with lamb wave", Composite Structures, Vol.237 (SCI)

Altay, Rana and Sadaghiani, Abdolali Khalili and Sevgen, İlker and Şişman, Alper and Koşar, Ali (2020) "Numerical and experimental studies on the effect of surface roughness and ultrasonic frequency on bubble dynamics in acoustic cavitation", Energies, Vol.13, No.5 (SCI, CPCI-S)

Abbasiasl, Taher and Niazi, Soroush and Sheibani Aghdam, Araz and Chen, Hongjian and Cebeci, Fevzi Çakmak and Ghorbani, Morteza and Grishenkov, Dmitry and Koşar, Ali (2020) "Effect of intensified cavitation using poly(vinyl alcohol) microbubbles on spray atomization characteristics in microscale", AIP Advances, Vol.10, No.2 (SCI)

Ghorbani, Morteza and Sheibani Aghdam, Araz and Talebian Gevari, Moein and Koşar, Ali and Cebeci, Fevzi Çakmak and Grishenkov, Dmitry and Svagan, Anna J. (2020) "Facile hydrodynamic cavitation on chip via cellulose nanofibers stabilized perfluorodroplets inside layer-by-layer assembled slips surfaces", Chemical Engineering Journal, Vol.382 (SCI)

Talebian Gevari, Moein and Hosseinpour Shafaghi, Ali and Villanueva, Guillermo and Ghorbani, Morteza and Koşar, Ali (2020) "Engineered lateral roughness element implementation and working fluid alteration to intensify hydrodynamic cavitating flows on a chip for energy harvesting", Micromachines, Vol.11, No.1 (SCI)

Roch, Tomas and Simurka, Lukas and Ow-Yang, Cleva W. and Sezen, Meltem and Satrapinskyy, Leonid and Türütoğlu, Tuncay (2020) "Periodic density fluctuations in sputtered aluminum-doped silicon oxynitride layers", International Journal of Applied Glass Science, Vol.11, No.1, 207-214 (SCI)

Ali, Hafiz Qasim and Emami Tabrizi, Isa and Khan, Raja Muhammad Awais and Tufani, Ali and Yıldız, Mehmet (2019) "Microscopic analysis of failure in woven carbon fabric laminates coupled with digital image correlation and acoustic emission", Composite Structures, Vol.230 (SCI)

Alijani Alijanvand, Hossein and Özbey, Arzu and Karimzadehkhouei, Mehrdad and Koşar, Ali (2019) "Inertial micromixing in curved serpentine micromixers with different curve angles", Fluids, Vol.4, No.4 (ESCI)

Emami Tabrizi, Isa and Khan, Raja Muhammad Awais and Massarwa, Eyass and Seyyed Monfared Zanjani, Jamal and Ali, Hafiz Qasim and Demir, Eralp and Yıldız, Mehmet (2019) "Determining tab material for tensile test of CFRP laminates with combined usage of digital image correlation and acoustic emission techniques", Composites Part A: Applied Science and Manufacturing, Vol.127 (SCI)

İnan Akmehmet, Güliz and Šturm, Sašo and Komelj, Matej and Samardžija, Zoran and Ambrožič, Bojan and Sezen, Meltem and Čeh, Miran and Ow-Yang, Cleva W. (2019) "Origin of long afterglow in strontium aluminate phosphors: atomic scale imaging of rare earth dopant clustering", Ceramics International, Vol.45, No.16, 20073-20077 (SCI)

Tofighi, Nima and Özbulut, Murat and Suleman, A. and Feng, J. J. and Yıldız, Mehmet (2019) "Dielectrophoretic interaction of circular particles in a uniform electric field", European Journal of Mechanics - B/Fluids, Vol.78, 194-202 (SCI)

Talebian Gevari, Moein and Ghorbani, Morteza and Svagan, Anna J. and Grishenkov, Dmitry and Koşar, Ali (2019) "Energy harvesting with micro scale hydrodynamic cavitation-thermoelectric generation coupling", AIP Advances, Vol.9, No.10 (SCI)

Çaldağ, Hakan Osman and Yeşilyurt, Serhat (2019) "Trajectories of magnetically-actuated helical swimmers in cylindrical channels at low Reynolds numbers", Journal of Fluids and Structures, Vol.90, 164-176 (SCI)

Ali, Hafiz Qasim and Emami Tabrizi, Isa and Khan, Raja Muhammad Awais and Seyyed Monfared Zanjani, Jamal and Yılmaz, Çağatay and Haghighi Poudeh, Leila and Yıldız, Mehmet (2019) "Experimental study on dynamic behavior of woven carbon fabric laminates using in-house piezoelectric sensors", Smart Materials and Structures, Vol.28, No.10 (SCI)

Emami Tabrizi, Isa and Kefal, Adnan and Seyyed Monfared Zanjani, Jamal and Akalın, Çağdaş and Yıldız, Mehmet (2019) "Experimental and numerical investigation on fracture behavior of glass/carbon fiber hybrid composites using acoustic emission method and refined zigzag theory", Composite Structures, Vol.223 (SCI)

Sheibani Aghdam, Araz and Ghorbani, Morteza and Deprem, Gökberk and Cebeci, Fevzi Çakmak and Koşar, Ali (2019) "A new method for intense cavitation bubble generation on layer-by-layer assembled slips", Scientific Reports, Vol.9, No.1 (SCI)

Pehlivan, Zeki Semih and Torabfam, Milad and Kurt, Hasan and Ow-Yang, Cleva W. and Hildebrandt, Niko and Yüce, Meral (2019) "Aptamer and nanomaterial based FRET biosensors: a review on recent advances (2014-2019)", Microchimica Acta, Vol.186, No.8 (SCI)

Kasap, Sibel and Kaya, İsmet İnönü and Repp, Sergej and Erdem, Emre (2019) "Superbat: battery-like supercapacitor utilized by graphene foam and zinc oxide (ZnO) electrodes induced by structural defects", Nanoscale Advances, Vol.1, No.7, 2586-2597 (SCI)

Zuvin, Merve and Kuruoğlu, Efe and Kaya, Veysel Oğulcan and Ünal, Özlem and Kutlu, Özlem and Yağcı Acar, Havva and Gözüaçık, Devrim and Koşar, Ali (2019) "Magnetofection of green fluorescent protein encoding DNA-bearing polyethyleneimine-coated superparamagnetic iron oxide nanoparticles to human breast cancer cells", ACS Omega, Vol.4, No.7, 12366-12374 (SCI)

Sadeghi, Sadra and Khabbazabkenar, Sirous and Ow-Yang, Cleva W. and Nizamoğlu, Sedat (2019) "Efficient white LEDs using liquid-state magic-sized CdSe quantum dots", Scientific Reports, Vol.9, No.1 (SCI)

Khaksaran, Mohammad Hadi and Kaya, İsmet İnönü (2019) "On the dynamics of intrinsic carbon in copper during the annealing phase of chemical vapor deposition growth of graphene", ACS Omega, Vol.4, No.6, 9629-9635 (SCI)

Motezakker, Ahmad Reza and Khalili Sadaghiani, Abdolali and Çelik, Süleyman and Larsen, Tom and Villanueva, Luis Guillermo and Koşar, Ali (2019) "Optimum ratio of hydrophobic to hydrophilic areas of biphilic surfaces in thermal fluid systems involving boiling", International Journal of Heat and Mass Transfer, Vol.135, 164-174 (SCI)

Demir, Eralp and Yousefi Louyeh, Pouya and Yıldız, Mehmet (2019) "Design of variable stiffness composite structures using lamination parameters with fiber steering constraint", Composites Part B: Engineering, Vol.165, 733-746 (SCI)

Fatehi, R. and Rahmat, Amin and Tofighi, N. and Yıldız, Mehmet and Shadloo, M. S. (2019) "Density-based smoothed particle hydrodynamics methods for incompressible flows", Computers and Fluids, Vol.185, 22-33 (SCI)

Bülbül, Gonca and Liu, Gökşin and Vithalapur, Namrata Rao and Atılgan, Canan and Sayers, Zehra and Pourmand, Nader (2019) "Employment of iron-binding protein from Haemophilus influenzae in functional nanopipettes for iron monitoring", ACS Chemical Neuroscience (SI), Vol.10, No.4, 1970-1977 (SCI)

Eskin, Murat Gökhan and Yeşilyurt, Serhat (2019) "Anode bleeding experiments to improve the performance and durability of proton exchange membrane fuel cells", International Journal of Hydrogen Energy, Vol.44, No.21, 11047-11056 (SCI)

Özbey, Arzu and Karimzadehkhouei, Mehrdad and Sefiane, Khellil and Koşar, Ali and Christy, John R. E. (2019) "On bubble dynamics in subcooled nucleate boiling on a platinum wire", International Journal of Thermal Sciences, Vol.137, 1-12 (SCI)

Sezen, Meltem and Ow-Yang, Cleva W. and Karahan, Özlem and Kıtıki, Burak (2018) "Micro and nanostructural analysis of a human tooth using correlated focused ion beam (FIB) and transmission Electron microscopy (TEM) investigations", Micron, Vol.115, 17-24 (SCI)

Sohouli, A. and Yıldız, Mehmet and Suleman, Afzal (2018) "Cost analysis of variable stiffness composite structures with application to a wind turbine blade", Composite Structures, Vol.203, 681-695 (SCI)

Ghorbani, Morteza and Chen, Hongjian and Villanueva, Luis Guillermo and Grishenkov, Dmitry and Koşar, Ali (2018) "Intensifying cavitating flows in microfluidic devices with poly(vinyl alcohol) (PVA) microbubbles", Physics of Fluids, Vol.30, No.10 (SCI)

Özbey, Arzu and Karimzadehkhouei, Mehrdad and Alijani Alijanvand, Hossein and Koşar, Ali (2018) "Microparticle inertial focusing in an asymmetric curved microchannel", Fluids, Vol.3, No.3 (ESCI)

Seyyed Monfared Zanjani, Jamal and Al-Nadhari, Abdulrahman Saeed Abdulqader and Yıldız, Mehmet (2018) "Manufacturing of electroactive morphing carbon fiber/glass fiber/epoxy composite: process and structural monitoring by FBG sensors", Thin-Walled Structures, Vol.130, 458-466 (SCI)

Bahmani Jalali, Houman and Aria, Mohammad Mohammadi and Dikbaş, Uğur Meriç and Sadeghi, Sadra and Kumar, Baskaran Ganesh and Şahin, Mehmet and Kavaklı, İbrahim Halil and Ow-Yang, Cleva W. and Nizamoğlu, Sedat (2018) "Effective neural photostimulation using indium-based type-II quantum dots", Acs Nano, Vol.12, No.8, 8104-8114 (SCI)

Mehrtash, Mehdi and Tari, İlker and Yeşilyurt, Serhat (2018) "Numerical modeling of visco-elasto-plastic hygro-thermal stresses and the effects of operating conditions on the mechanical degradation of PEFC membranes", Journal of Power Sources, Vol.396, 164-174 (SCI)

Ghorbani, Morteza and Khalili Sadaghiani, Abdolali and Villanueva, L. Guillermo and Koşar, Ali (2018) "Hydrodynamic cavitation in microfluidic devices with roughened surfaces", Journal of Micromechanics and Microengineering, Vol.28, No.7 (SCI)

Mohammadi, Ali and Koşar, Ali (2018) "Review on heat and fluid flow in micro pin fin heat sinks under single-phase and two-phase flow conditions", Nanoscale and Microscale Thermophysical Engineering, Vol.22, No.3, 153-197 (SCI)

Özbey, Arzu and Karimzadehkhouei, Mehrdad and Bayrak, Özgecan and Koşar, Ali (2018) "Inertial focusing of microparticles in curvilinear microchannels with different curvature angles", Microfluidics and Nanofluidics, Vol.22, No.6 (SCI)

Yüce, Meral and Kurt, Hasan and Hussain, Babar and Ow-Yang, Cleva W. and Budak, Hikmet (2018) "Exploiting stokes and anti-stokes type emission profiles of aptamer-functionalized luminescent nanoprobes for multiplex sensing applications", Chemistry Select, Vol.3, No.21, 5814-5823 (SCI)

Kocaman, Esat Selim and Yılmaz, Çağatay and Deniz, Ataman and Yıldız, Mehmet (2018) "The performance of embedded fiber Bragg grating sensors for monitoring failure modes of foam cored sandwich structures under flexural loads", Journal of Sandwich Structures and Materials, Vol.20, No.5, 553-577 (SCI)

Adatoz, E. Beruhil and Hendessi, Saman and Ow-Yang, Cleva W. and Demirel, A. Levent (2018) "Restructuring of poly(2-ethyl-2-oxazoline)/tannic acid multilayers into fibers", Soft Matter, Vol.14, No.19, 3849-3857 (SCI)

Karimzadehkhouei, Mehrdad and Shojaeian, Mostafa and Khalili Sadaghiani, Abdolali and Şendur, Kürşat and Mengüç, M. Pınar and Koşar, Ali (2018) "Entropy generation analysis of laminar flows of water-based nanofluids in horizontal minitubes under constant heat flux conditions", Entropy, Vol.20, No.4 (SCI)

Sadeghi, Sadra and Bahmani Jalali, Houman and Melikov, Rustamzhon and Kumar, Baskaran Ganesh and Mohammadi Aria, Mohammad and Ow-Yang, Cleva W. and Nizamoğlu, Sedat (2018) "Stokes-shift-engineered indium phosphide quantum dots for efficient luminescent solar concentrators", ACS Applied Materials & Interfaces, Vol.10, No.15, 12975-12982 (SCI)

Ozbulut, M. and Tofighi, N. and Goren, O. and Yıldız, Mehmet (2018) "Investigation of wave characteristics in oscillatory motion of partially filled rectangular tanks", Journal of Fluids Engineering, Transactions of the ASME, Vol.140, No.4 (SCI)

Ghorbani, Morteza and Sözer, Canberk and Alcan, Gökhan and Ünel, Mustafa and Ekici, Sinan and Üvet, Hüseyin and Koşar, Ali (2018) "Biomedical device prototype based on small scale hydrodynamic cavitation", AIP Advances, Vol.8, No.3 (SCI)

Seyyed Monfared Zanjani, Jamal and Saner Okan, Burcu and Pappas, Panagiotis-Nektarios and Galiotis, Costas and Menceloğlu, Yusuf Z. and Yıldız, Mehmet (2018) "Tailoring viscoelastic response, self-heating and deicing properties of carbon-fiber reinforced epoxy composites by graphene modification", Composites Part A: Applied Science and Manufacturing, Vol.106, 1-10 (SCI)

Ross, Caroline Jane and Atılgan, Ali Rana and Taştan Bishop, Özlem and Atılgan, Canan (2018) "Unraveling the motions behind Enterovirus 71 uncoating", Biophysical Journal, Vol.114, No.4, 822-838 (SCI)

Khalili Sadaghiani, Abdolali and Koşar, Ali (2018) "Numerical investigations on the effect of fin shape and surface roughness on hydrothermal characteristics of slip flows in microchannels with pin fins", International Journal of Thermal Sciences, Vol.124, 375-386 (SCI)

Yılmaz, Çağatay and Akalın, Çağdaş and Günal, İbrahim and Çelik, Hakan and Büyük, Murat and Suleman, Afzal and Yıldız, Mehmet (2018) "A hybrid damage assessment for E-and S-glass reinforced laminated composite structures under in-plane shear loading", Composite Structures, Vol.186, 347-354 (SCI)

Sadaghiani, Abdolali Khalili and Saadi, Nazwat S. and Semsari Parapari, Sorour and Karabacak, Tansel and Keskinöz, Mehmet and Koşar, Ali (2017) "Boiling heat transfer performance enhancement using micro and nano structured surfaces for high heat flux electronics cooling systems", Applied Thermal Engineering, Vol.127, 484-498 (SCI)

Motezakker, Ahmad Reza and Khalili Sadaghiani, Abdolali and Akkoç, Yunus and Semsari Parapari, Sorour and Gözüaçık, Devrim and Koşar, Ali (2017) "Surface modifications for phase change cooling applications via crenarchaeon Sulfolobus solfataricus P2 bio-coatings", Scientific Reports, Vol.7 (SCI)

Abdizadeh, Haleh and Atılgan, Ali Rana and Atılgan, Canan and Dedeoğlu, Burcu (2017) "Computational approaches for deciphering the equilibrium and kinetic properties of iron transport proteins", Metallomics, Vol.9, No.11, 1513-1533 (SCI)

Avaz, Merve Senem and Oğuz, Oğuzhan and Kurt, Hasan and Menceloğlu, Yusuf Z. and Atılgan, Canan (2017) "Soft segment length controls morphology of poly(ethylene oxide) based segmented poly(urethane-urea) copolymers in a binary solvent", Computational Materials Science, Vol.138, 58-69 (SCI)

Ghorbani, Morteza and Mohammadi, Ali and Motezakker, Ahmad Reza and Villanueva, Luis Guillermo and Leblebici, Yusuf and Koşar, Ali (2017) "Energy harvesting in microscale with cavitating flows", ACS Omega, Vol.2, No.10, 6870-6877 (ESCI)

Brown, David K. and Penkler, David L. and Amamuddy, Olivier Sheik and Ross, Caroline and Atılgan, Ali Rana and Atılgan, Canan and Bishop, Özlem Taştan (2017) "MD-TASK: a software suite for analyzing molecular dynamics trajectories", Bioinformatics, Vol.33, No.17, 2768-2771 (SCI)

Özbey, Arzu and Karimzadehkhouei, Mehrdad and Sefiane, Khellil and Koşar, Ali (2017) "Changing bubble dynamics in subcooled boiling with TiO2 nanoparticles on a platinum wire", Journal of Molecular Liquids, Vol.242, 456-470 (SCI)

Sohouli, A. and Yıldız, Mehmet and Suleman, A. (2017) "Design optimization of thin-walled composite structures based on material and fiber orientation", Composite Structures, Vol.176, 1081-1095 (SCI)

Rahmat, Amin and Koç, Bahattin and Yıldız, Mehmet (2017) "A systematic study on numerical simulation of electrified jet printing". Published Online First http://dx.doi.org/10.1016/j.addma.2017.08.004

Seyyed Monfared Zanjani, Jamal and Saner Okan, Burcu and Yılmaz, Çağatay and Menceloğlu, Yusuf Z. and Yıldız, Mehmet (2017) "Monitoring the interface and bulk self-healing capability of tri-axial electrospun fibers in glass fiber reinforced epoxy composites", Composites Part A: Applied Science and Manufacturing, Vol.99, 221-232 (SCI)

Akgönül, Sarp and Özbey, Arzu and Karimzadehkhouei, Mehrdad and Gözüaçık, Devrim and Koşar, Ali (2017) "The effect of asymmetry on micromixing in curvilinear microchannels", Microfluidics and Nanofluidics, Vol.21, No.7 (SCI)

Jamalabadi, Mohammad Yaghoub Abdollahzadeh and DaqiqShirazi, Mohammadreza and Koşar, Ali and Shadloo, Mostafa Safdari (2017) "Effect of injection angle, density ratio, and viscosity on droplet formation in a microfluidic T-junction". Published Online First http://dx.doi.org/10.1016/j.taml.2017.06.002

Penkler, David and Şensoy, Özge and Atılgan, Canan and Tastan Bishop, Özlem (2017) "Perturbation-response scanning reveals key residues for allosteric control in Hsp70", Journal of Chemical Information and Modeling, Vol.57, No.6, 1359-1374 (SCI)

Esmaeili Aliabadi, Danial and Kaya, Murat and Şahin, Güvenç (2017) "Competition, risk and learning in electricity markets: an agent-based simulation study", Applied Energy, Vol.195, 1000-1011 (SCI, SSCI)

Ullah, Mohib and Seyyed Monfared Zanjani, Jamal and Haghighi Poudeh, Leila and Siddiq, M. and Saner Okan, Burcu and Yıldız, Mehmet and Menceloğlu, Yusuf Z. (2017) "Manufacturing functionalized mono-crystalline diamond containing electrospun fibers reinforced epoxy composites with improved mechanical characteristics", Diamond and Related Materials, Vol.76, 90-96 (SCI)

Abdizadeh, Haleh and Atılgan, Ali Rana and Atılgan, Canan (2017) "Mechanisms by which salt concentration moderates the dynamics of human serum transferrin", Journal of Physical Chemistry B, Vol.121, No.18, 4778-4789 (SCI)

Özden-Yenigün, Elif and Atılgan, Canan and Elliott, James A. (2017) "Multi-scale modelling of carbon nanotube reinforced crosslinked interfaces", Computational Materials Science, Vol.129, 279-289 (SCI)

Vasileva, G. Yu and Smirnov, D. and Vasilyev, Yu B. and Nestoklon, M. O. and Averkiev, N. S. and Novikov, S. and Kaya, İsmet İnönü and Haug, R. J. (2017) "Strongly temperature dependent resistance of meander-patterned graphene", Applied Physics Letters, Vol.110, No.11 (SCI)

Önol, Aykut Özgün and Yeşilyurt, Serhat (2017) "Effects of wind gusts on a vertical axis wind turbine with high solidity", Journal of Wind Engineering and Industrial Aerodynamics, Vol.162, 1-11 (SCI)

Kurt, Hasan and Alpaslan, Ece and Yıldız, Burçin and Taralp, Alpay and Ow-Yang, Cleva W. (2017) "Conformation-mediated Forster resonance energy transfer (FRET) in blue-emitting polyvinylpyrrolidone (PVP)-passivated zinc oxide (ZnO) nanoparticles", Journal of Colloid and Interface Science, Vol.488, 348-355 (SCI)

Ghorbani, Morteza and Sadaghiani, Abdolali Khalili and Yıldız, Mehmet and Koşar, Ali (2017) "Experimental and numerical investigations on spray structure under the effect of cavitation phenomenon in a microchannel", Journal of Mechanical Science and Technology, Vol.31, No.1, 235-247 (SCI)

Yüksel, Tuğçe and Litster, Shawn and Viswanathan, Venkatasubramanian and Michalek, Jeremy J. (2017) "Plug-in hybrid electric vehicle LiFePO4 battery life implications of thermal management, driving conditions, and regional climate", Journal of Power Sources, Vol.338, 49-64 (SCI)

Esmaeili Aliabadi, Danial and Kaya, Murat and Şahin, Güvenç (2016) "Determining collusion opportunities in deregulated electricity markets", Electric Power Systems Research, Vol.141, 432-441 (SCI)

Khalili Sadaghiani, Abdolali and Yıldız, Mehmet and Koşar, Ali (2016) "Numerical modeling of convective heat transfer of thermally developing nanofluid flows in a horizontal microtube", International Journal of Thermal Sciences, Vol.109, 54-69 (SCI)

Şişman, Yağmur and Khalili Sadaghiani, Abdolali and Khedir, Khedir R. and Brozak, Matthew and Karabacak, Tansel and Koşar, Ali (2016) "Subcooled flow boiling over microstructured plates in rectangular minichannels", Nanoscale and Microscale Thermophysical Engineering, Vol.20, No.3-4, 173-190 (SCI)

Shojaeian, Mostafa and Yıldızhan, Melike Mercan and Coşkun, Ömer and Özkalay, Ebrar and Tekşen, Yiğit and Gülgün, Mehmet Ali and Yağcı Acar, Havva and Koşar, Ali (2016) "Investigation of change in surface morphology of heated surfaces upon pool boiling of magnetic fluids under magnetic actuation", Materials Research Express, Vol.3, No.9 (SCI)

Akay, Erdem and Yılmaz, Çağatay and Kocaman, Esat Selim and Türkmen, Halit S. and Yıldız, Mehmet (2016) "Monitoring Poisson's ratio degradation of FRP composites under fatigue loading using biaxially embedded FBG sensors", Materials, Vol.9, No.9 (SCI)

Kurt, Hasan and Ow-Yang, Cleva W. (2016) "Impedance spectroscopy analysis of the photophysical dynamics due to the nanostructuring of anode interlayers in organic photovoltaics". Published Online First http://dx.doi.org/10.1002/pssa.201600314

Yılmaz, Çağatay and Akalın, Çağdaş and Kocaman, Esat Selim and Suleman, A. and Yıldız, Mehmet (2016) "Monitoring Poisson's ratio of glass fiber reinforced composites as damage index using biaxial Fiber Bragg Grating sensors", Polymer Testing, Vol.53, 98-107 (SCI)

Ghorbani, Morteza and Yıldız, Mehmet and Gözüaçık, Devrim and Koşar, Ali (2016) "Cavitating nozzle flows in micro- and minichannels under the effect of turbulence", Journal of Mechanical Science and Technology, Vol.30, No.6, 2565-2581 (SCI)

İnan Akmehmet, Güliz and Sturm, Saso and Bocher, Laura and Kociak, Mathieu and Ambrozic, Bojan and Ow-Yang, Cleva W. (2016) "Structure and luminescence in long persistence Eu, Dy, and B codoped strontium aluminate phosphors: the Boron effect", Journal of the American Ceramic Society, Vol.99, No.6, 2175-2180 (SCI)

Ghorbani, Morteza and Alcan, Gökhan and Ünel, Mustafa and Gözüaçık, Devrim and Ekici, Sinan and Üvet, Hüseyin and Şabanoviç, Asif and Koşar, Ali (2016) "Visualization of microscale cavitating flow regimes via particle shadow sizing imaging and vision based estimation of the cone angle". Published Online First http://dx.doi.org/10.1016/j.expthermflusci.2016.04.026

Nedaei, Masoumeh and Armağan, Efe and Sezen, Meltem and Özaydın İnce, Gözde and Koşar, Ali (2016) "Enhancemet of flow boiling heat transfer in pHEMA/pPFDA coated microtubes with longitudinal variations in wettability", AIP Advances, Vol.6, No.3 (SCI)

Khalili Sadaghiani, Abdolali and Koşar, Ali (2016) "Numerical and experimental investigation on the effects of diameter and length on high mass flux subcooled flow boiling in horizontal microtubes", International Journal of Heat and Mass Transfer, Vol.92, 824-837 (SCI)

Seyyed Monfared Zanjani, Jamal and Saner Okan, Burcu and Menceloğlu, Yusuf Z. and Yıldız, Mehmet (2016) "Nano-engineered design and manufacturing of high-performance epoxy matrix composites with carbon fiber/selectively integrated graphene as multi-scale reinforcements", RSC Advances, Vol.6, No.12, 9495-9506 (SCI)

Abdizadeh, Haleh and Güven, Gökçe and Atılgan, Ali Rana and Atılgan, Canan (2015) "Perturbation response scanning specifies key regions in subtilisin serine protease for both function and stability", Journal of Enzyme Inhibition and Medicinal Chemistry, Vol.30, No.6, 867-873 (SCI)

Özbaykal, Gizem and Atılgan, Ali Rana and Atılgan, Canan (2015) "In silico mutational studies of Hsp70 disclose sites with distinct functional attributes", Proteins: Structure, Function and Bioinformatics, Vol.83, No.11, 2077-2090 (SCI)

İzci, Türker and Koz, Mustafa and Koşar, Ali (2015) "The effect of micro pin-fin shape on thermal and hydraulic performance of micro pin-fin heat sinks", Heat Transfer Engineering, Vol.36, No.17, 1447-1457 (SCI)

Karimzadehkhouei, Mehrdad and Yalçın, Sinan Eren and Şendur, Kürşat and Mengüç, Pınar and Koşar, Ali (2015) "Pressure drop and heat transfer characteristics of nanofluids in horizontal microtubes under thermally developing flow conditions", Experimental Thermal and Fluid Science (SI), Vol.67, 37-47 (SCI)

Haghighi Poudeh, Leila and Saner Okan, Burcu and Seyyed Monfared Zanjani, Jamal and Yıldız, Mehmet and Menceloğlu, Yusuf Z. (2015) "Design and fabrication of hollow and filled graphene-based polymeric spheres via core-shell electrospraying", RSC Advances, Vol.5, No.111, 91147-91157 (SCI)

Acemoğlu, Alperen and Yeşilyurt, Serhat (2015) "Effects of poiseuille flows on swimming of magnetic helical robots in circular channels", Microfluidics and Nanofluidics (SCI)

Seyyed Monfared Zanjani, Jamal and Saner Okan, Burcu and Letofsky-Papst, Ilse and Menceloğlu, Yusuf Z. and Yıldız, Mehmet (2015) "Repeated self-healing of nano and micro scale cracks in epoxy based composites by tri-axial electrospun fibers including different healing agents", RSC Advances, Vol.5, No.89, 73133-73145 (SCI)

Demircan, Özgür and Yılmaz, Çağatay and Kocaman, Esat Selim and Tang, S. and Hamada, H. and Yıldız, Mehmet (2015) "Effect of fiber densities on impact properties of biaxial warp-knitted textile composites", Journal of Reinforced Plastics and Composites, Vol.34, No.16, 1287-1297 (SCI)

Abdizadeh, Haleh and Atılgan, Ali Rana and Atılgan, Canan (2015) "Detailed molecular dynamics simulations of human transferrin provide insights into iron release dynamics at serum and endosomal pH", Journal of Biological Inorganic Chemistry, Vol.20, No.4, 705-718 (SCI)

Kocaman, Esat Selim and Keulen, Casey J. and Akay, Erdem and Yıldız, Mehmet and Türkmen, Halit S. and Suleman, Afzal (2015) "An experimental study on the effect of length and orientation of embedded FBG sensors on the signal properties under fatigue loading". Published Online First http://dx.doi.org/10.1515/secm-2014-0029

Shadloo, Mostafa S. and Weiss, Robert and Yıldız, Mehmet and Dalrymple, Robert A. (2015) "Numerical simulation of long wave runup for breaking and nonbreaking waves", International Journal of Offshore and Polar Engineering, Vol.25, No.1, 1-7 (SCI)

Shojaeian, Mostafa and Yıldız, Mehmet and Koşar, Ali (2015) "Convective heat transfer and second law analysis of non-Newtonian fluid flows with variable thermophysical properties in circular channels", International Communications in Heat and Mass Transfer, Vol.60, 21-31 (SCI)

Acemoğlu, Alperen and Temel, Fatma Zeynep and Yeşilyurt, Serhat (2014) "Characterization and modeling of micro swimmers with helical tails and cylindrical heads inside circular channels", Journal of Fluids Engineering, Vol.136, No.12 (SCI)

Shojaeian, Mostafa and Yıldız, Mehmet and Koşar, Ali (2014) "Heat transfer characteristics of plug flows with temperature-jump boundary conditions in parallel-plate channels and concentric annuli", International Journal of Thermal Sciences, Vol.84, 252-259 (SCI)

Rahmat, Amin and Tofighi, Nima and Safdari Shadloo, Mostafa and Yıldız, Mehmet (2014) "Numerical simulation of wall bounded and electrically excited Rayleigh-Taylor instability using incompressible smoothed particle hydrodynamics", Colloids and Surfaces A: Physicochemical and Engineering Aspects, Vol.460, 60-70 (SCI)

Demir, Ebru and İzci, Türker and Alagöz, Arif Sinan and Karabacak, Tansel and Koşar, Ali (2014) "Effect of silicon nanorod length on horizontal nanostructured plates in pool boiling heat transfer with water", International Journal of Thermal Sciences, Vol.82, 111-121 (SCI)

Mısırlıoğlu, Burç and Yıldız, Mehmet (2014) "Carrier accumulation near electrodes in ferroelectric films due to polarization boundary conditions", Journal of Applied Physics, Vol.116, No.2 (SCI)

Çıkım, Taha Abdullah and Armağan, Efe and Özaydın İnce, Gözde and Koşar, Ali (2014) "Flow boiling enhancement in microtubes with crosslinked pHEMA coatings and the effect of coating thickness", Journal of Heat Transfer, Vol.136, No.8 (SCI)

Kaya, Alihan and Özdemir, Mehmed Rafet and Keskinöz, Mehmet and Koşar, Ali (2014) "The effects of inlet restriction and tube size on boiling instabilities and detection of resulting premature critical heat flux in microtubes using data analysis", Applied Thermal Engineering, Vol.65, No.1-2, 575-587 (SCI)

Shojaeian, Mostafa and Koşar, Ali (2014) "Convective heat transfer and entropy generation analysis on Newtonian and non-Newtonian fluid flows between parallel-plates under slip boundary conditions", International Journal of Heat and Mass Transfer, Vol.70, No.3, 664-673 (SCI)

Özel, Burcu and Örüm, Aslıhan and Yıldız, Mehmet and Menceloğlu, Yusuf Z. (2014) "Experimental study on the rheology of anisotropic, flocculated and low volume fraction colloids", Korea-Australia Rheology Journal, Vol.26, No.1, 105-116 (SCI)

Keulen, Casey J. and Yıldız, Mehmet and Suleman, Afzal (2014) "Damage detection of composite plates by Lamb wave ultrasonic tomography with a sparse hexagonal network using damage progression trends", Shock and Vibration (SCI)

Korkmaz, Gözde and Tekirdağ, Kumsal Ayşe and Özturk, Deniz Gülfem and Koşar, Ali and Sezerman, Uğur and Gözüaçık, Devrim (2013) "MIR376A is a regulator of starvation-induced autophagy", PLoS One, Vol.8, No.12 (SCI)

Kaya, Alihan and Demiryürek, Rıdvan and Armağan, Efe and Özaydın İnce, Gözde and Sezen, Meltem and Koşar, Ali (2013) "Boiling heat transfer enhancement in mini/microtubes via polyhydroxyethylmethacrylate (pHEMA) coatings on inner microtube walls at high mass fluxes", Journal of Micromechanics and Microengineering, Vol.23, No.11 (SCI)

Temel, Fatma Zeynep and Erman, Aydek Gökçe and Yeşilyurt, Serhat (2013) "Characterization and modeling of biomimetic untethered robots swimming in viscous fluids inside circular channels", IEEE/ASME Transactions on Mechatronics, Vol.19, No.5, 1562-1573 (SCI)

Safdari Shadloo, Mostafa and Rahmat, Amin and Yıldız, Mehmet (2013) "A smoothed particle hydrodynamics study on the electrohydrodynamic deformation of a droplet suspended in a neutrally buoyant Newtonian fluid", Computational Mechanics, Vol.52, No.3, 693-707 (SCI)

Özden-Yenigün, Elif and Şimşek, Eren and Menceloğlu, Yusuf Z. and Atılgan, Canan (2013) "Molecular basis for solvent dependent morphologies observed on electrosprayed surfaces", Physical Chemistry Chemical Physics, Vol.15, No.41, 17862-17872 (SCI)

Sadek, Samir Hassan Mahmoud and Yıldız, Mehmet (2013) "Modeling die swell of second-order fluids using smoothed particle hydrodynamics", Journal of Fluids Engineering, Vol.135, No.5 (SCI)

Yanık, Cenk and Kaya, İsmet İnönü (2013) "Local breakdown of the quantum Hall effect in narrow single layer graphene Hall devices", Solid State Communications, Vol.160, 47-51 (SCI)

Şeşen, Muhsincan and Demir, Ebru and İzci, Türker and Khudhayer, Wisam and Karabacak, Tansel and Koşar, Ali (2013) "Submerged jet impingement cooling using nanostructured plates", International Journal of Heat and Mass Transfer, Vol.59, 414-422 (SCI)

Mısırlıoğlu, Burç and Yıldız, Mehmet (2013) "Dielectric response of fully and partially depleted ferroelectric thin films and inversion of the thickness effect", Journal of Physics D: Applied Physics, Vol.46, No.12 (SCI)

Zainali, Amir and Tofighi, Nima and Safdari Shadloo, Mostafa and Yıldız, Mehmet (2013) "Numerical investigation of Newtonian and non-Newtonian multiphase flows using ISPH method", Computer Methods in Applied Mechanics and Engineering, Vol.254, 99-113 (SCI)

Temel, Fatma Zeynep and Yeşilyurt, Serhat (2013) "Simulation-based analysis of micro-robots swimming at the center and near the wall of circular mini-channels", Microfluidics and Nanofluidics, Vol.14, No.1-2, 287-298 (SCI)

Rastani, Sina and Yüksel, Tuğçe and Çatay, Bülent, "Electric vehicle routing problem with time windows and cargo weight", Smart and Sustainable Supply Chain and Logistics – Trends, Challenges, Methods and Best Practices, Golinska-Dawson, Paulina and Tsai, Kune-Muh and Kosacka-Olejnik, Monika (eds.), Switzerland: Springer, Cham, December 2020, 175-190

Haghighi Poudeh, Leila and Yıldız, Mehmet and Menceloğlu, Yusuf Z. and Saner Okan, Burcu, "Three-dimensional graphene-based structures: production methods, properties, and applications", Handbook of Graphene: Growth, Synthesis, and Functionalization, Celasco, Edvige and Chaika, Alexander N. (eds.), USA: Wiley-Scrivener, July 2019, 359-387

Seyyed Monfared Zanjani, Jamal and Saner Okan, Burcu and Menceloğlu, Yusuf Z. and Yıldız, Mehmet, "Self-healing thermosetting composites: concepts, chemistry and future advances", Hybrid Organic‐Inorganic Interfaces: Towards Advanced Functional Materials, Delville, Marie-Helene and Taubert, Andreas (eds.), UK: Wiley, September 2018

Alcan, Gökhan and Ghorbani, Morteza and Koşar, Ali and Ünel, Mustafa, "Single droplet tracking in jet flow", Image Analysis and Recognition: 13th International Conference, ICIAR 2016, in Memory of Mohamed Kamel, Póvoa de Varzim, Portugal, July 13-15, 2016, Proceedings, Campilho, Aurello and Karray, Fakhri (eds.), Switzerland: Springer International Publishing, July 2016, 415-422

Rocha, B. and Silva, C. and Keulen, C. and Yıldız, Mehmet and Suleman, A., "New trends in SHM, structural health monitoring of aircraft structures", New Trends in Structural Health Monitoring, Wieslaw, Ostachowicz and Güemes, Alfredo (eds.), Germany: Springer, January 2013

Yüksel, Tuğçe, "Thermal and performance modeling of electric vehicle batteries [Elektrikli araç bataryaları için sıcaklık ve performans modellenmesi]", 24th Congress on Thermal Science and Technology with International Participation (Ulibtk'23), Baskent University, December 2023, 340-350

Topal, Serra and Beylergil, Bertan and Yıldırım, Ceren and Ünal, Serkan and Yıldız, Mehmet, "Advancing aircraft repair patch prepregs: enhancing composite performance through resin type, cure cycle, and nanomaterial innovations", 3rd Global Conference on Advanced Nanotechnology & Nanomaterials, Berlin, Germany: Peers Alley Media, September 2023

Atılgan, Canan and Liu, Gökşin and Jalalpour, Farzaneh and Ekmen, Erhan and Berksöz, Melike and Atılgan, Ali Rana and Sayers, Zehra, "Increased ionic strength triggers multiple conformations in both apo and holo forms of bacterial ferric binding protein", Biophysical Society Annual Meeting, Elsevier, February 2023, 444A-445A

Salamatgharamaleki, Saeed and Ateşpare, Asu Ece and Kohlan, Taha Behroozi and Ünal, Serkan and Menceloğlu, Yusuf Z. and Yıldız, Mehmet and Dızman, Bekir, "Synthesis and characterization of hydrolyzed polyoxazolines and investigation of their curing capabilities", Doğan, Muhittin (ed.), 5th International Eurasian Conference on Biological and Chemical Sciences (EurasianBioChem 2022), EurasianBioChem, December 2022, 136-136

Karimi, Sasan and Barzegar Osgouei, Ali and Yıldız, Mehmet and Şaş Çaycı, Hatice Sinem, "Parametric study of afp lay-up process parameters effect on the air permeability of thermoplastic composites and their suitability for out of autoclave post-processing by a new method", Vassilopoulos, A. P. and Michaud, V. (eds.), 20th European Conference on Composite Materials: Composites Meet Sustainability, ECCM 2022, Composite Construction Laboratory (CCLab), Ecole Polytechnique Federale de Lausanne (EPFL), June 2022, 981-989

Abdollahzadeh, Mohammadamin and Kefal, Adnan and Yıldız, Mehmet, "Shape sensing of a doubly curved aft fuselage panel using inverse finite element method", 9th International Workshop on Metrology for AeroSpace (MetroAeroSpace), IEEE (Institute of Electrical and Electronics Engineers), June 2022, 362-367

Barzegar Osgouei, Ali and Karimi, Sasan and Şaş Çaycı, Hatice Sinem and Yıldız, Mehmet, "Investigating the effect of ply orientation on the surface thermal history of newly placed tape during thermoplastic composite manufacturing with lafp process", Vassilopoulos, A. P. and Michaud, V. (eds.), 20th European Conference on Composite Materials: Composites Meet Sustainability, ECCM 2022, Composite Construction Laboratory (CCLab), Ecole Polytechnique Federale de Lausanne (EPFL), June 2022, 210-217

Şahin, Osman and Koşar, Ali and Yapıcı, Murat Kaya, "Modeling the dielectrophoretic separation of red blood cells (RBCs) from B-Lymphocytes (B-Cells)", 43rd Annual International Conference of the IEEE Engineering in Medicine & Biology Society (EMBC), Institute of Electrical and Electronics Engineers, November 2021, 1238-1241

Malekabadi, Fatemeh and Çaldağ, Hakan O. and Yeşilyurt, Serhat, "Acoustic radiation forces and torques on compressible micro rings in standing waves", 74th Annual Meeting of the APS Division of Fluid Dynamics, Amerıcan Physical Society, November 2021

Marques, Ricardo and Rodrigues, Francisco and Emami Tabrizi, Isa and Kefal, Adnan and Ali, Hafiz Qasim and Yıldız, Mehmet and Suleman, Afzal, "Probabilistic approach for thermoelastic signal source identification in carbon fiber/epoxy composite materials using digital image correlation", 24th International Conference on Composite Structures (ICCS24), University of Porto, June 2021, 162-162

Dayan, Alp Recep and Yeşilyurt, Serhat, "Modeling and simulations for magnetic manipulation of micro objects with a visual control system [Görüntü işlemeli kontrol sistemi ile mikro objelerin manyetik manipülasyonu için modelleme ve benzeşim çalışması]", 29th Signal Processing and Communications Applications Conference (SIU), Institute of Electrical and Electronics Engineers, June 2021

Bilal, Diyar Khalis and Ünel, Mustafa and Yıldız, Mehmet and Koç, Bahattin, "Localization and estimation of bending and twisting loads using neural networks", 46th Annual Conference of the IEEE Industrial Electronics Society (IECON 2020), IEEE Computer Society, October 2020, 489-494

Çaldağ, Hakan Osman and Yeşilyurt, Serhat, "A simple numerical tool for the evaluation of acoustic radiation force on helices", IEEE International Ultrasonics Symposium (IUS), IEEE Computer Society, September 2020

Çaldağ, Hakan Osman and Yeşilyurt, Serhat, "Steering control of magnetic helical swimmers in swirling flows due to confinement", IEEE International Conference on Robotics and Automation (ICRA), IEEE (Institute of Electrical and Electronics Engineers), September 2020, 6994-7000

Aboubakri, Akam and Yanık, Cenk and Akkuş, Yiğit and Koşar, Ali and Sadaghiani, Abdolali Khalili, "Numerical and experimental investigation on evaporation of water droplet on surfaces with mixed wettability", ASME 2020 18th International Conference on Nanochannels, Microchannels, and Minichannels, ICNMM 2020, collocated with the ASME 2020 Heat Transfer Summer Conference and the ASME 2020 Fluids Engineering Division Summer Meeting, American Society of Mechanical Engineers, July 2020

Mohammadpour Chehrghani, Mirvahid and Abbasiasl, Taher and Gharib, Ghazaleh and Koşar, Ali and Sadaghiani, Abdolali Khalili, "Steam flow condensation on superhydrophobic surfaces in a high aspect ratio microchannel", ASME 2020 18th International Conference on Nanochannels, Microchannels, and Minichannels, ICNMM 2020, collocated with the ASME 2020 Heat Transfer Summer Conference and the ASME 2020 Fluids Engineering Division Summer Meeting, American Society of Mechanical Engineers, July 2020

Rahmat, Amin and Yıldız, Mehmet, "Numerical simulation of a rising bubble under the influence of electric forces using ISPH method", Owen, R. and De Borst, R. and Reese, J. and Pearce, C. (eds.), 6th ECCOMAS European Conference on Computational Mechanics: Solids, Structures and Coupled Problems, ECCM 2018 and 7th ECCOMAS European Conference on Computational Fluid Dynamics, ECFD 2018, International Centre for Numerical Methods in Engineering, CIMNE, January 2020, 2223-2233

Sohouli, Abdolrasoul and Kefal, Adnan and Yıldız, Mehmet and Suleman, Afzal, "Multi-material topology optimization of structures using peridynamics", 30th International Conference on Adaptive Structures and Technologies (ICAST2019), Concordia University, October 2019

Babaie Rizvandi, Omid and Yeşilyurt, Serhat, "Effects of PEM fuel cell degradation on the transport properties of the cathode catalyst layer", 11th International Conference on Applied Energy (ICAE2019), Energy Proceedings, August 2019

Emami Tabrizi, Isa and Zanjani, J. Seyyed Monfared and Yıldız, Mehmet, "Investigation of damage accumulation in glass/carbon fiber hybrid composites through acoustic emission method", 22nd International Conference on Composites Materials (ICCM22), Melbourne: International Committee on Composite Materials, August 2019, 1907-1915

Niazi, Soroush and Talebian Gevari, Moein and Ghorbani, Morteza and Koşar, Ali, "Deagglomeration effects of hydrodynamic cavitation on nanofluids", 1st International Conference on Nanofluids (ICNf2019) and 2nd European Symposium on Nanofluids (ESNf2019), Bubok Publishing S.L, July 2019, 476-479

Ramezanzadeh, Shayan and Özbulut, M. and Yıldız, Mehmet, "Simulation of irregular wave motion using a flap-type wavemaker", Bensow, R. and Ringsberg, J. (eds.), VIII. International Conference on Computational Methods in Marine Engineering (MARINE 2019), International Centre for Numerical Methods in Engineering, May 2019, 771-782

Yılmaz, C. and Akalın, C. and Günal, I. and Çelik, H. and Büyük, M. and Suleman, A. and Yıldız, Mehmet, "Observation of damage accumulation under in-plane shear loading", Specialists' Meeting AVT-305 on Sensing Systems for Integrated Vehicle Health Management (IVHM) of Military Vehicles (NATO STO AVT-305), NATO Science & Technology Organization, December 2018

Erdöl, Sevim and Ow-Yang, Cleva W. and Sezen, Meltem and Büyükaksoy, Aligül, "La0.6 Sr0.4 CoO3 thin film cathodes prepared by polymeric precursors for solid oxid fuel cells", Turan, Servet and Kara, Alpagut and Başkaya, Mutlu (eds.), IV. International Ceramic, Glass, Porcelain, Enamel, Glaze and Pigment Congress (SERES'18), Anadolu University, Eskişehir Technical University, October 2018, 557-557

Ghorbani, Morteza and Villanueva, Guillermo and Koşar, Ali, "An optimization study on thermal energy harvesting from micro cavitating flows", 6th Micro and Nano Flows Conference 2018, Brunel University, October 2018

Demir, Ebru and Yeşilyurt, Serhat, "Rolling and sliding of spheres inside horizontal channels", Haliyo, S. and Sill, A. and Arai, F. and Fatikow, S. (eds.), International Conference on Manipulation, Automation and Robotics at Small Scales (MARSS), IEEE (Institute of Electrical and Electronics Engineers), October 2018

Kefal, Adnan and Sohouli, A. and Öterkuş, E. and Yıldız, Mehmet and Suleman, A., "Topology optimization of cracked structures using peridynamics", 28th International Workshop on Computational Mechanics of Materials (IWCMM), University of Strathclyde, September 2018

Rizvandi, Omid Babaie and Yeşilyurt, Serhat, "Modeling of flow distribution in proton exchange membrane fuel cell", 16th International Conference on Nanochannels, Microchannels and Minichannels (ICNMM2018), ASME (American Society of Mechanical Engineers), June 2018

Madenci, Erdoğan and Kefal, Adnan and Dördüncü, Mehmet and Barut, Atila and Yıldız, Mehmet, "Isogeometric analysis using peridynamics and XFEM", 59th AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, American Institute of Aeronautics and Astronautics, January 2018

Ceh, Miran and Sturm, Saso and Jancar, Bostjan and Recnik, Aleksander and Daneu, Nina and Drazic, Goran and Jeric, Marja and Kosir, Mateja and Presecnik, Matej and Bernik, Slavko and Ow-Yang, Cleva W. and Gülgün, Mehmet Ali and De Boor, Johannes, "HRTEM and HRSTEM investigations of oxide thermoelectric materials", Gajovic, Andrea and Weber, I. and Kovacevic, G. and Cadez, V. and Segota, S. and Peharec Stefanic, P. and Vidos, Ana (eds.), 13th Multinational Congress on Microscopy, Ruđer Bošković Institute and Croatian Microscopy Society, September 2017, 8-10

Sözer, Canberk and Ghorbani, Morteza and Alcan, Gökhan and Üvet, Hüseyin and Ünel, Mustafa and Koşar, Ali, "Design, prototyping and control of a flexible cystoscope for biomedical applications", 4th International Conference on Mechanics and Mechatronics Research (ICMMR 2017), IOP Publishing, August 2017

Sadaghiani, Abdolali Khalili and Motezakker, Ahmad Reza and Koşar, Ali, "Experimental studies on steam condensation in horizontal and vertical microtubes", 13th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics (HEFAT 2017), American Society of Thermal and Fluids Engineers, June 2017

Keçebaş, Muhammed Ali and Mengüç, M. Pınar and Koşar, Ali and Şendur, Kürşat, "Passive radiative cooling system design with periodic high-low index segments", 3rd International Workshop on Nano-Micro Thermal Radiation (NanoRad 2017), KAIST, June 2017

Önol, Aykut Özgün and Onat, Ahmet and Yeşilyurt, Serhat, "Comparisons of controller performance for small-scale verti-cal axis wind turbines", 2017 American Control Conference, IEEE (Institute of Electrical and Electronics Engineers), May 2017

Yeşilyurt, Serhat and Babaie Rizvandi, Omid, "Design and optimization of anode flow field of a large proton exchange membrane fuel cell for high hydrogen utilization", 69th Annual Meeting of the APS Division of Fluid Dynamics, American Physical Society, November 2016

Yeşilyurt, Serhat and Çaldağ, Hakan Osman, "Trajectories of artificial microswimmers with helical tails inside circular channels", 69th Annual Meeting of the APS Division of Fluid Dynamics, American Physical Society, November 2016

Önol, Aykut Özgün and Sancar, Uğur and Onat, Ahmet and Yeşilyurt, Serhat, "Modeling, hardware-in-the-loop simulations and control design for small-scale vertical axis wind turbines", 9th ASME Annual Dynamic Systems and Control Conference (DSCC2016), ASME (American Society of Mechanical Engineers), October 2016

Babaie Rizvandi, Omid and Yeşilyurt, Serhat, "Design of anode flow channels and headers for a large PEMFC operating at ultra-low stoichiometric flow conditions at the anode exit", ASME 2016 14th International Conference on Nanochannels, Microchannels, and Minichannels (ICNMM2016), ASME (American Society of Mechanical Engineers), July 2016

Khalili Sadaghiani, Abdolali and Şişman, Yağmur and Özaydın İnce, Gözde and Koşar, Ali, "An experimental study on flow boiling characteristics of phema nano-coated surfaces in a microchannel", 5th ASME International Conference on Micro/Nanoscale Heat and Mass Transfer (MNHMT2016), ASME (American Society of Mechanical Engineers), January 2016

Şişman, Yağmur and Sadaghiani, Abdolali Khalili and Khedir, Ramazan and Karabacak, Tansel and Koşar, Ali, "Nucleate boiling heat transfer enhancement using nanostructured al-alloy plates", 5th ASME International Conference on Micro/Nanoscale Heat and Mass Transfer, ASME (American Society of Mechanical Engineers), January 2016

Çaldağ, Hakan Osman and Yeşilyurt, Serhat, "Position and trajectrories of helical microswimmers inside circular channels", 68th Annual Meeting of the APS Division of Fluid Dynamics, Boston, Massachusetts: APS (American Physical Society), November 2015

Önol, Aykut Özgün and Sancar, Uğur and Onat, Ahmet and Yeşilyurt, Serhat, "Model predictive control for energy maximization of small vertical axis wind turbines", ASME 2015 Dynamic Systems and Control Conference (DSCC2015), USA: ASME (American Society of Mechanical Engineers), October 2015

Şınlak, Adnan and Kaleli, Can and Önol, Aykut Özgün and Yeşilyurt, Serhat, "Küçük dikey eksenli rüzgâr türbini için basit kontrol tasarımı (Simple control design for a small vertical axis wind turbine)", Otomatik Kontrol Türk Milli Komitesi Ulusal Toplantısı (TOK'2015), Denizli, Türkiye: Pamukkale Üniversitesi, September 2015, 95-99

Özden Yenigün, Elif and Atılgan, Canan and Elliott, James, "Tuning interface via multi-scale modeling for superior carbon nanotube-polymer nanocomposites/ Yarns", 20th International Conference on Composite Materials (ICCM20), Copenhagen, Denmark: International Committee on Composite Materials, July 2015

Tofighi, Nima and Özbulut, Murat and Rahmat, Amin and Feng, James J. and Yıldız, Mehmet, "Migration of a rigid disc in couette flow subject to an external electric field simulated using ISPH", Schrefler, Bernhard A. and Oñate, Eugenio and Papadrakakis, Manolis (eds.), 6th International Conference on Computational Methods for Coupled Problems in Science and Engineering (COUPLED PROBLEMS), Barcelona, Spain: CIMNE (International Center for Numerical Methods in Engineering), May 2015, 725-733

Özbulut, Murat and Tofighi, Nima and Gören, Ömer and Yıldız, Mehmet, "On the SPH modelling of flow over cylinder beneath to a free-surface", VI International Conference on Computational Methods in Marine Engineering (Marine 2015), Barcelona, Spain: CIMNE (International Center for Numerical Methods in Engineering) 2015

Üzüşen, Doğan and Oral, Özlem and Ekici, Sinan and Ünel, Mustafa and Gözüaçık, Devrim and Koşar, Ali, "Assessment of probe-to-specimen distance effect in kidney stone treatment with hydrodynamic cavitation", 4th European Conference on Microfluidics (Microfluidics 2014), Limerick, Ireland: University of Limerick, December 2014

Temel, Fatma Zeynep and Yeşilyurt, Serhat, "Confined swimming of bio-inspired magnetic microswimmers in rectangular channels", 67th Annual Meeting of the APS Division of Fluid Dynamics, San Francisco, California: APS (American Physical Society), November 2014

Acemoğlu, Alperen and Yeşilyurt, Serhat, "Magnetic helical microswimmers in poiseuille flow", 67th Annual Meeting of the APS Division of Fluid Dynamics, San Francisco, California: APS (American Physical Society), November 2014

İnan Akmehmet, Güliz and Ceh, Miran and Sturm, Saso and Ow-Yang, Cleva W., "Determination of structure and chemistry of long-persistence strontium aluminate phosphor compounds in aberration-corrected tem/stem", Hozak, Pavel (ed.), 18th International Microscopy Congress, Prague, Czech Republic: International Federation of Microscopy Societies, September 2014, 2976-2977

Shojaeian, Mostafa and Zamanian, Rahim and Koşar, Ali, "The effect of radiative heat transfer on slip flow through parallel-plate microchannels", 15th International Heat Transfer Conference, Kyoto, Japan: International Heat Transfer Conference Organization, September 2014

Demircan, Özgür and Yılmaz, C. and Kocaman, E. S. and Akay, E. and Yıldız, Mehmet, "Tensile and bending properties of biaxial warp knitted textile composites", 1st Joint Turkey-Japan Workshop (JTJW) on Polymeric Composite Materials, Istanbul, Turkey: Sabanci University, May 2014

Monfared Zanjani, Jamal Seyyed and Saner Okan, Burcu and Yıldız, Mehmet and Menceloğlu, Yusuf Z., "Fabrication and morphological investigation of multi-walled electrospun polymeric nanofibers", MRS Fall 2013 Meeting, Warrendale, PA, USA: Materials Research Society 2014

Shojaeian, Mostafa and Koşar, Ali, "Numerical investigation of fully developed fluid flow and heat transfer in double-trapezoidal microchannels", ASME 2013 International Mechanical Engineering Congress & Exposition, New York, NY, USA: ASME (American Society of American Engineers), November 2013

Işıkel Şanlı, Lale and Alkan Gürsel, Selmiye and Yeşilyurt, Serhat, "Design and modeling of high temperature water free proton exchange membranes in DEA PEMFC operations", 224th ECS Meeeting, San Francisco, California: Electrochemical Society, November 2013, 789-794

Özden Yenigün, Elif and Şimşek, Eren and Menceloğlu, Yusuf Z. and Atılgan, Canan, "Theoretical and experimental investigation of dual-scale roughness via electro-spraying", 246th National Meeting of the American-Chemical-Society (ACS), Washington, DC, USA: American Chemical Society, September 2013

Tofighi, Nima and Rahmat, Amin and Yıldız, Mehmet, "Numerical simulation of buoyancy driven droplet rising under influence of an electrical field using ISPH", III International Conference on Particle-Based Methods: Fundamentals and Applications (Particles 2013), Spain: ECCOMAS, September 2013

Chen, Jixin and Siegel, Jason B. and Matsuura, Toyoaki and Stefanopoulou, Anna G. and Yeşilyurt, Serhat, "Experimental validation of equilibria in fuel cells with dead-ended anodes", European Control Conference 2013, USA: IEEE (Institute of Electrical and Electronics Engineers), July 2013

Özbey, Arzu and Karimzadehkhouei, Mehrdad and Kurtoğlu, Evrim and Koşar, Ali, "Simulation of magnetic actuation of ferrofluids in microtubes", 11th International Conference on Nanochannels, Microchannels, and Minichannels (ICNMM2013), New York, NY: ASME (American Society of Mechanical Engineers), July 2013

Acemoğlu, Alperen and Temel, Fatma Zeynep and Yeşilyurt, Serhat, "Characterization and modeling of micro swimmers with helical tails and cylindrical heads inside circular channels", 11th International Conference on Nanochannels, Microchannels, and Minichannels (ICNMM2013), United States: ASME (American Society of Mechanical Engineers), June 2013

Tofighi, Nima and Yıldız, Mehmet, "Incompressible smoothed particle hydrodynamics simulation of three phase flows", 21st Annual Conference of the CFD Society of Canada, Sherbrooke, Canada: CFD Society of Canada, May 2013

Atılgan, Canan and Güven, Gökçe and Atılgan, Ali Rana, "Structural basis of how ferric binding proteins utilize pH differences for controlled release of iron", 57th Annual Meeting of the Biophysical-Society, Cambridge, MA, USA: Biophysical Society, January 2013, 212A-212A

Melemez, Fazlı Fatih and Boz, Talha and Chelliah, Pandian and Bektaş, Gökhan and Yıldız, Mehmet and Öztürk, Cem and Menceloğlu, Yusuf Z., "Study of local and transient buckling in glass fiber reinforced composite using fiber bragg grating", Hristoforou, E. and Vlachos, D. S. (eds.), 2nd International Conference on Materials and Applications for Sensors and Transducers (IC-MAST), Zurich, Switzerland: Trans Tech Publications 2013, 346-351